THAKA AI · FIELD ORGANISERS

Original camping files you can print

Twelve original dry-use accessory prototypes, supplied directly here. Every package contains the actual STL, editable millimetre source, a bilingual manual and its licence.

Download all original files Renewable-energy CAD studies

Find a printable accessory

THAKA AI · CC0 · STL + SCAD

USB cable winding card

Low-voltage cable storage; use a loose figure-eight and respect the cable bend radius.

Verified model dimensions XYZ: 80 × 35 × 3 mm
Mesh triangles: 236

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

Guyline storage winder

Store dry cord only; remove the winder before tensioning the line. Not a tensioner, anchor or climbing device.

Verified model dimensions XYZ: 90 × 38 × 3.2 mm
Mesh triangles: 432

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

Gear identification tag

Use a marker or paper label and a soft tie; avoid publishing sensitive personal details.

Verified model dimensions XYZ: 60 × 25 × 2.4 mm
Mesh triangles: 400

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

Spare zipper pull tab

Light bag-zipper grip only; inspect the existing slider and use a suitable soft connecting loop.

Verified model dimensions XYZ: 35 × 12 × 3 mm
Mesh triangles: 400

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

Four-slot dry cable organiser

Open storage slots are 6, 7.5, 9 and 10.5 mm; measure your cable. Not electrical strain relief.

Verified model dimensions XYZ: 72 × 25 × 4 mm
Mesh triangles: 268

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

Tent-peg storage comb

Holds pegs together in a bag; cover sharp tips separately. Never use as a peg, anchor or tent load path.

Verified model dimensions XYZ: 110 × 28 × 5 mm
Mesh triangles: 300

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

Small dry-parts tray

Open tray for small dry items inside an existing protective case; not waterproof or food-safe certified.

Verified model dimensions XYZ: 90 × 60 × 15 mm
Mesh triangles: 412

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

Dry-box divider with feet

Free-standing divider for a dry storage box; adjust length to your existing box and keep latches/vents clear.

Verified model dimensions XYZ: 90 × 30 × 40 mm
Mesh triangles: 76

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

Ventilated power-bank rest

Dry resting surface for an intact certified power bank; not a battery enclosure, heat shield or vehicle mount.

Verified model dimensions XYZ: 110 × 65 × 15 mm
Mesh triangles: 128

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

100 mm field reference ruler

Check the printed 100 mm length against a physical ruler; use only for non-critical field measurements.

Verified model dimensions XYZ: 100 × 22 × 3 mm
Mesh triangles: 348

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

30-degree solar setup gauge

Angle reference beside a ground panel only; not a panel support, wind anchor or solar tracker.

Verified model dimensions XYZ: 60 × 12 × 34.64 mm
Mesh triangles: 8

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

THAKA AI · CC0 · STL + SCAD

Reusable dry label-and-tie strip

Organise dry low-weight accessories with soft ties; this strip is not a rated restraint or electrical insulator.

Verified model dimensions XYZ: 80 × 18 × 2.4 mm
Mesh triangles: 596

Closed mesh and dimensions checked. Physical printing, strength and field performance remain unverified.

STL + editable source + instructions STL file SCAD

Full instructions and printer requirements →

From editable file to your printer

Measure the real cable, box or accessory. Open the SCAD source and edit its named top parameters in millimetres. Render the complete solid, then export STL.
In your slicer, select the exact printer, firmware, nozzle and material. Import at 100% in millimetres and confirm XYZ against the file record.
Place a broad stable face on the bed. A 0.4 mm nozzle and 0.2 mm layer are planning examples only. Use the printer/filament profile for temperatures, walls, infill, speed, cooling and supports.
Check every layer, overhang and travel move. Generate G-code only for that machine. Print one fit sample before a batch.
Cool, remove burrs and check dimensions, cracks, flexibility and contact with the real item. Recheck after heat, sun or abrasion; replace damaged prints.

Printer and material

Use an FFF printer with a verified usable volume larger than the part plus brim/edge clearance. PETG can suit many dry accessories; use a supported profile. Prolonged UV/heat needs an appropriate material and, where required, ventilation/enclosure. PLA may deform in hot cars or desert sun.

Use limits

These are organisers and measurement references. Do not use for climbing, anchors, pressurised water, filter membranes, food contact, battery cells, live electrics or hot stove parts. A mesh check does not certify service performance.

Original model licence CC0 1.0

Keep existing third-party renewable-energy packages with their original licence notices. CC0 here applies to the newly authored Thaka accessory geometry, not to every file in the older collection.

Verification and reuse notes →